How Do You Know When an Icemaker for Kenmore Lg Refrigerator Need Replacing

Sound Diagnosis

During normal operation, refrigerators can make different noises. Below are some examples of mutual refrigerator noises, press the to listen to the sound or click the words to see their causes and solutions to eliminate noises that are non associated with normal performance.

F/R Compartment Fan

Frequency:

Near always on

Caption:

The freezer and Fridge compartment fans run almost all the time to help broadcast cold air through out the entire unit and reduce compartment temperatures.

Diagnostic:

This sound is Normal.

Frost Build up on F/R Compartment Fan

Note: The fans turn off when the door is opened.

Frequency:

Almost ever on

Explanation:

Frost buildup on the fridge or freezer fan tin can cause this sound to occur.

Diagnostic:

To verify if this dissonance is being acquired by the fan, open up the refrigerator door. If the noise stops, this is near likely the consequence. The noise will usually go away after the fridge automatically defrosts. If the noise does not go away later defrost then the fridge needs to exist manually defrosted.

Damper

Frequency:

Once an 60 minutes

Explanation:

LG Refrigerators employ Dampers and 3 way valves to help control and distribute airflow to the Refrigerator and Freezer compartments.

Diagnostic:

This audio is Normal.

Case Shrink & Expansion

Frequency:

Every 4 to 12 hours

Explanation:

Normally LG refrigerators will automatically defrost twice a day. During and after defrost, the refrigerator case tin sometimes make a racket equally information technology shrinks and expands.

Diagnostic:

This sound is Normal.

Refrigerant menstruation noise

Frequency:

Every 2 hours

Caption:

This audio can be heard every couple of hours when oil and refrigerant menstruum over the exit of the inner bike pipe.

Diagnostic:

This sound is Normal.

Compressor

Frequency:

Almost e'er on

Explanation:

When the compressor operates, its pump draws in the cold refrigerant gas from the evaporator. It is then the compressors chore to heat up the gas. The compressor is louder after the defrost cycle considering information technology requires more endeavor to reduce the temperature again.

Diagnostic:

This sound is Normal.

3 Style Valve

Frequency:

Once an hour

Explanation:

LG refrigerators use dampers and a 3 way valve to help command and distribute airflow to the refrigerator and freeze compartments.

Diagnostic:

This sound is Normal.

Cooling Room Fan

Frequency:

Well-nigh ever on

Explanation:

The compressor has to work to reduce the compartment temperature. When running, the compressor radiates estrus into the machine room. The fridge uses the machine room fan to reduce temperature in the machine room.

Diagnostic:

This sound is Normal.

Ice Maker on Without H2o Connected

Frequency:

Every 90 minutes

Explanation:

If the water supply to your Refrigerator is non continued or fully open you may hear a periodic buzzing Noise.

Diagnostic:

This can exist resolved past turning the ice maker OFF until the water supply issue is corrected.

Clicking

Frequency:

Every 12 hours

Explanation:

Clicking noises come up from the defrost command when the automatic defrost cycle begins and ends. The thermostat command will also click when cycling on and off.

Diagnostic:

This sound is Normal.

Rattling

Frequency:

    Random

Explanation:

1. Rattling noises may come from the flow of refrigerant, the water line on the back of the unit, or items stored on the tiptop, or effectually the fridge. The sound is likewise caused when the fridge is non resting solidly on the floor.

   Recommended solution: None, this is a normal performance

---

2. The audio is besides caused when the refrigerator is not resting solidly on the flooring.

   Recommended solution: If the floor is weak or uneven, movement the unit of measurement to a written report floor; otherwise, the leveling legs need to be adjusted.

---

3. When refrigerator with linear compressor is jarred while running, it will trigger the dissonance for few seconds.

Recommended solution: None, this is a normal functioning

Sizzling

Frequency:

Every 4 Hours

Explanation:

As frost melts and water drips onto the defrost heater, it will make a sizzling or hissing sound equally it evaporates .

Diagnostic:

This sound is Normal.

Vibrating

Frequency:

Random

Caption:

This Racket occurs if the doors are not properly aligned, the fridge is non level, the flooring nether the Fridge is not level, or the Fridge is touching a cabinet or wall. These sounds may also exist caused by items inside or nearby the refrigerator.

Diagnostic:

To eliminate this noise, make sure that the sides and dorsum of the Refrigerator are not touching a wall or cabinet. Make sure that the Refrigerator, Refrigerator doors, and floor under the unit of measurement are level. Adjust the leveling feet down to give the unit a backward gradient. Also, bank check for items inside the refrigerator that may exist contacting the inner walls while the unit is running and check for any items resting confronting or on top of the refrigerator.

Dripping

Frequency:

Every 12 hours or Twice a Day

Explanation:

This noise occurs during the defrost bike when h2o drips into the drain pan.

Diagnostic:

This audio is Normal.

Back Adjacent Dwelling house

Normal Sounds

Abnormal Sounds

Clicking Audio

1. This is a normal operation, the clicking noise is coming from the defrost control. The defrost control will click when the automatic defrost wheel begins and ends.

2. The thermostat control (or refrigerator control on some models) will also click when cycling on and off.

Recommended solution: None, this is a normal functioning.

Rattling Sound

1. Rattling noises may come from the catamenia of refrigerant, the h2o line on the back of the unit, or items stored on the summit, or around the refrigerator.

   Recommended solution: None, this is a normal operation

---

2. The sound is also caused when the refrigerator is non resting solidly on the flooring.

   Recommended solution: If the flooring is weak or uneven, move the unit to a study flooring; otherwise, the leveling legs need to exist adjusted.

3. When refrigerator with linear compressor is jarred while running, it volition trigger the noise for few seconds.

Recommended solution: None, this is a normal operation

Whooshing Sound

1. Evaporator's fan motor is circulating air through the refrigerator and freezer compartments.

2. Air is being forced over the condenser by the condenser fan.

Recommended solution: None, this is a normal operation

Gurgling Sound

1. Refrigerant is flowing through the cooling system.

Recommended solution: None, this is a normal operation.

Popping Sound

1. The popping noise is due to the contraction and expansion of the inside walls due to changes in temperature.

Recommended solution: None, this is a normal operation

Sizzling Sound

1. Sizzling sound is due to water dripping on the defrost heater during a defrost cycle.

Recommended Solution: None, this is a normal performance

Vibrating Sound

1. If the side or dorsum of the refrigerator is touching a chiffonier or wall, some of the normal vibrations may make an aural sound.

Recommended Solution: To eliminate the racket, make sure that the sides and back cannot vibrate against any wall or cabinet.

Dripping Sound

1. Dripping noise is caused past water running into the drain pan during the defrost bike.

Recommended Solution: None, this is a normal functioning

Pulsating Loftier-pitch Sound

1. Your fridge is designed to run more efficiently to keep your nutrient items at the desired temperature. The high efficiency compressor may crusade your new fridge to run longer than your old i, simply information technology is still more energy efficient than previous models. While the fridge is running, it is normal to hear a pulsating or loftier-pitched sound.

Recommended Solution: None, this is a normal operation

Humming and Buzzing Sound

1. The humming and buzzing dissonance is coming from the compressor.

   The compressor noise is supposed to be normal operation, and it is non supposed to last more i hr, but if the noise is loud enough to be heard from another room, and then the unit requires a repair service.

   Before we conclude that the noise occurs all the fourth dimension and the unit of measurement requires a repair service, let'south become a closer expect at the compressor. At that place are two types of compressors, the linear compressor and standard compressor.

   LINEAR COMPRESSOR:

   Units with linear compressors can ofttimes be recognized hands by the insignia located on the control panel.

   

   The linear compressor will modify speeds according to the needs of the refrigerator in order to absurd both the refrigerator and freezer compartments effectively. This change in speed will produce more activeness on the compressor, which in turn results to an increased sound. If the compressor goes into a higher speed than normal, it can make noises that resemble buzzing, knocking, or banging.

   If this sort of unexpected noise continues for more than ane hour at a fourth dimension, the unit will crave a repair service. Delight visit our Request a Repair page for a professional service.

   STANDARD COMPRESSOR:

   The standard compressor will make a low buzzing or humming noise during normal operation. But if the noise becomes louder or tin can be heard from another room, the unit will require a repair service. Delight visit our Asking a Repair page for a professional person service.

Popping and Tapping Audio

1. Popping or tapping sounds can occur for xxx - 90 seconds when the compressor begins to run, this is common to models that are equipped with a linear compressor.

2. Popping or tapping sounds may also occur if the unit of measurement is moved while information technology is in operation.

   The compressor noise is supposed to be normal functioning, and information technology is not supposed to concluding more than 1 hour, merely if the noise is loud enough to exist heard from another room, then the unit requires a repair service.

   Before nosotros conclude that the noise occurs all the fourth dimension and the unit requires a repair service, let'southward get a closer look at the compressor. There are two types of compressors, the linear compressor and standard compressor.

   LINEAR COMPRESSOR:

   Units with linear compressors can often be recognized hands by the insignia located on the control panel.

   

   The linear compressor will change speeds according to the needs of the fridge in society to cool both the refrigerator and freezer compartments effectively. This change in speed will produce more activity on the compressor, which in turn results to an increased sound. If the compressor goes into a college speed than normal, information technology can make noises that resemble buzzing, knocking, or banging.

   If this sort of unexpected dissonance continues for more than than 1 hour at a time, the unit volition crave a repair service. Please visit our Request a Repair folio for a professional person service.

   STANDARD COMPRESSOR:

   The standard compressor volition make a low buzzing or humming noise during normal operation. Just if the noise becomes louder or can be heard from some other room, the unit volition crave a repair service. Please visit our Request a Repair page for a professional service.

Vibrating and Rattling Audio

For these types of dissonance problems, the following items should exist in society:

1. The doors must be properly aligned.

2. The refrigerator chiffonier should be leveled.

3. The flooring where the fridge is installed should be as level as possible.

If any of the above is affecting the unit, it volition cause the fridge to brand racket during operation. The to a higher place factors are all parts of proper installation.

Annotation: if the leveling legs are not adjusted downwards, this sound may occur. to eliminate this audio adjust the leveling downward to the floor giving the unit a backwards slope.

These sounds may also be acquired by items inside or nearby the refrigerator

• An particular inside the refrigerator that is contacting i of the inner walls may vibrate when the unit of measurement is running.

• An item resting confronting or touching the cabinet of the refrigerator could as well cause noise.

Note: If nothing is resting against the sides, peak, or front of the refrigerator, try pulling information technology abroad from the wall slightly (almost an inch or more) to see if the racket stops. If information technology does it may be been caused by the water line resting against the dorsum of the unit

Hissing and Gurgling Sound

These sounds might be equally a result of the machine defrost cycle, or they could be coming from the sealed system components.

• As the frost melts and h2o drips onto the defrost heater, it volition make a hissing sound every bit it evaporates.

Gurgling noise can also come up from the sealed organisation as refrigerant moves through its components.

• Typically, car defrost is set to run every four hours. For newer models, the defrost cycle interval will exist shortened depending on how oftentimes the doors are opened.

Annotation: Normal operational noises tin can be louder depending on the installation environment.

1. Is the noise coming from the fridge or door alert?

2. Does the fridge take a h2o dispenser?

   Yes No

3. 

   Does information technology manipulate water?

   Yep No

4. Does the refrigerator have an icemaker?

   Yes No

5. Does the noise occur when you are dispensing water?

   Yes No

6. Does the noise stop when the doors are opened?

   Yes No

8. Does the noise terminate when the doors are opened?

   Yes No

11. This noise may be coming from the icemaker when the water supply is not connected to information technology.

    The reasons for this sort of dissonance:

    • During normal fridge operation, when the icemaker is turned ON, the refrigerator's water valve will activate and vibrate for a few seconds as the ice maker requests for water.

    • If the icemaker is turned ON simply the Water SUPPLY IS Non CONNECTED the refrigerator will make a buzzing or clicking audio that can go louder and more persistent.

    How to set the problem:

    • Plough OFF THE ICEMAKER until you decide to connect a water supply, and this volition eliminate the noise yous are experiencing.

12. This dissonance is caused when the domicile water pressure is a bit too high. You tin partially close the h2o valve connected to the refrigerator to decrease the pressure. This will reduce such dissonance.

    How to bank check the water pressure:

    • Get a standard size coffee cup (8 ounce).

    • Make full the cup with water from the refrigerator's water dispenser.

    • Count how many seconds it takes to fill the cup.

    How long does information technology accept to fill the cup?

    Less than 4 Seconds More than than 4 Seconds

13. This noise may be caused by the water supply line. The water supply line shifts intermittently as the water valve opens and closes, and can strike the wall or back of the refrigerator, causing a thumping or vibrating sound. In general, this is a normal functioning.

    To reduce this normal operation dissonance:

    1. Pull the unit of measurement abroad from the wall slightly, or reposition the h2o line backside the unit to eliminate the noise.

    
    H2o supply lines behind the refrigerator

    
    Unit of measurement making vibrating sound when it is too close to the wall

    
    Pull the unit of measurement away from the wall or reposition h2o line

    Depending on the installation status, the habitation h2o supply line tin can hit the wall, floor, and refrigerator. Please re-arrange the home water supply line, and cheque the dissonance again.

    Does this step reduce the noise?

    Yeah No

14. The water pressure is TOO HIGH. Conform the habitation water valve to reduce the pressure level.

    How to adjust home water valve:

    • Close off the water at your house's internal water chief.

    • Plow the shut off valve completely to the right (turn water supply off).

    • Loosen the locking nut on the water pressure regulator by turning it to the left.

    • Plough the adjusting spiral to the left to reduce the water pressure, or to the right to increase the water pressure level.

    • Allow few hours for the refrigerator to regulate, and monitor the dissonance reduction.

    This adjustment depends on your home water valve installation, if you are non sure about how to suit domicile water valve, do a quick search on any search engine for this topic, you lot may too demand the help of a plumber for proper adjustment.

    Does this step reduce the noise?

    Yes No

15. Your water pressure is NORMAL inside 4 seconds and a little more. Simply if the water takes longer to fill, then the water pressure is as well low. Having confirmed that your water pressure is normal, proceed to the side by side troubleshooting step.

    Keep to Next Stride

16. Proficient job, now that we have been able to reduce the noise of your refrigerator, continue the troubleshooting steps to check for other contributing factors that tin can lead to refrigerator noises.

    Continue to Side by side Step

17. Okay, If you take tried the steps in a higher place, but the dissonance still persists; continue with the troubleshooting steps. At that place are other contributing factors that can cause refrigerator noises.

    Proceed to Side by side Step

18. Determine if the noise is acquired past high water pressure or from the h2o lines.

19. This noise may be coming from the icemaker when the h2o supply is not connected to it.

    The reasons for this sort of racket:

    • During normal refrigerator functioning, when the icemaker is turned ON, the refrigerator'due south water valve will activate and vibrate for a few seconds as the ice maker requests for water.

    • If the icemaker is turned ON simply the WATER SUPPLY IS Non Connected the fridge will brand a buzzing or clicking sound that can get louder and more persistent.

    How to fix the problem:

    • Plough OFF THE ICEMAKER until you decide to connect a h2o supply, and this volition eliminate the noise you are experiencing.

20. Skilful job, now that we have been able to reduce the noise of your refrigerator, continue the troubleshooting steps to check for other contributing factors that can lead to refrigerator noises.

    Proceed to Next Step

21. Okay, If y'all have tried the steps to a higher place, but the dissonance nevertheless persists; continue the troubleshooting steps. In that location are other contributing factors that can cause refrigerator noises.

    Proceed to Adjacent Step

22. Door hinges, door stopper and proper leveling

    Noises that occur when the doors are opening or closing typically do non crave a repair service. They are primarily related to door hinges, door stopper and proper leveling.

    DOOR HINGES:

    Noises from the door hinges may sound like grinding or squeaking.

    Recommended solution: Employ a nutrient grade silicon grease to cease the noise. Food grease are availble for auction at local edifice supply stores. If you are not certain of what to look for, please ask a sales acquaintance to help you observe it.

    DOOR STOPPER:

    A popping sound that occurs while the door is opened or closed can be coming from the auto endmost hinge or door stopper. Some models may not have a stopper on the closing hinge.

    

    Recommended solution: For LFC, LFX, or LMX models, the latch on the underside of the fridge door may be dirty or dry. Clean the latch and apply a food form silicon grease to stop the noise.

    PROPER LEVELING:

    Proper leveling of the refrigerator, and the alignment of the door(s) of the unit are very important for proper performance of the unit of measurement.

    Steps for proper leveling:

    The following steps are snippets culled from our detailed article about proper leveling. Please visit our LG Refrigerator Leveling Instructions page for a step by step guide.

    

    • Open the fridge doors.

    • Place a level on tiptop of the refrigerator to check if the unit is leveled from side to side.

    • If a level is not available, make full a drinking glass half full of water, set it on top of the refrigerator to gauge if the unit is leveled.

    • The fridge legs should exist adapted for the unit to have a slight backward slope.

    • Check the door alignment.

    • Fifty-fifty if your refrigerator cabinet is leveled, the doors should be properly aligned too.

24. This noise may be coming from the compressor which is supposed to be normal functioning. The racket is not supposed to last more than than 1 hr, but if the noise is loud enough to exist heard from another room, then the unit of measurement requires a repair service.

    Before we conclude that the racket occurs all the fourth dimension and the unit requires a repair service, let's get a closer look at the compressor. There are two types of compressors, the linear compressor and standard compressor.

    LINEAR COMPRESSOR:

    Units with linear compressors tin oft be recognized easily past the insignia located on the command panel.

    

    The linear compressor will modify speeds according to the needs of the refrigerator in order to cool both the fridge and freezer compartments effectively. This change in speed volition produce more activity on the compressor, which in turn results to an increased sound. If the compressor goes into a college speed than normal, information technology tin can make noises that resemble buzzing, knocking, or banging.

    If this sort of unexpected noise continues for more ane hour at a time, the unit will crave a repair service. Please visit our Request a Repair page for a professional service.

    STANDARD COMPRESSOR:

    The standard compressor will brand a depression buzzing or bustling noise during normal operation. But if the noise becomes louder or can exist heard from another room, the unit volition require a repair service. Please visit our Request a Repair page for a professional service.

25. Compressor noises are a office of normal refrigerator operation; still compressor noises are not supposed to last longer than 1 hour and should not be loud enough to hear in another room. Let'due south take a closer look at the compressor to determine if your fridge needs a repair service. There are two types of compressors, the linear compressor and standard compressor.

    LINEAR COMPRESSOR:

    Units with linear compressors can often be recognized hands by the insignia located on the control panel.

    

    The linear compressor will change speeds according to the needs of the refrigerator in gild to cool both the refrigerator and freezer compartments effectively. This alter in speed will produce more than activeness on the compressor, which in plow results to an increased audio. If the compressor goes into a higher speed than normal, it tin can brand noises that resemble buzzing, knocking, or banging.

    If this sort of unexpected noise continues for more than one hour at a fourth dimension, the unit of measurement will require a repair service. Please visit our Request a Repair page for a professional service.

    STANDARD COMPRESSOR:

    The standard compressor volition brand a low buzzing or humming dissonance during normal operation. Merely if the noise becomes louder or can be heard from another room, the unit of measurement volition require a repair service. Please visit our Request a Repair page for a professional service.

26. This noise may be coming from the compressor. Compressor noises are a part of normal refrigerator operation; however compressor noises are not supposed to last longer than i hour and should not be loud enough to hear in another room. Let's accept a closer wait at the compressor to determine if your refrigerator needs a repair service

    In that location are ii types of compressors, the linear compressor and standard compressor.

    LINEAR COMPRESSOR:

    Linear compressors can often exist recognized easily by the insignia located on the control console.

    

    The linear compressor will change speeds according to the needs of the fridge in guild to cool both the refrigerator and freezer compartments effectively. This change in speed volition produce more activity on the compressor, which in turn results to an increased sound. If the compressor goes into a higher speed than normal, it tin can brand noises that resemble buzzing, knocking, or banging.

    If this sort of unexpected racket continues for more than one hour at a time, the unit will require a repair service. Delight visit our Request a Repair page for a professional service.

    STANDARD COMPRESSOR:

    The standard compressor will make a low buzzing or humming racket during normal operation. But if the dissonance becomes louder or can be heard from another room, the unit will require a repair service. Please visit our Request a Repair page for a professional service.

27. Persistent noise that stops when the doors are opened is usually caused past the refrigerator fans. The unit uses fans to assistance circulate air through the compartments. These fans end spinning when y'all open the refrigerator doors. If the noise starts to return before long later you lot close the doors, then this dissonance is typically caused past frost buildup around the fan'southward housing which can be resolved by proper leveling and temperature adjustment.

    PROPER LEVELING:

    The post-obit steps are snippets culled from our detailed article about proper leveling. Please visit our LG Fridge Leveling Instructions page for a pace by step guide.

    

    • Open the refrigerator doors.

    • Place a level on the top of the refrigerator to check if the unit information technology is leveled from side to side.

    • If a level is not bachelor, fill up a drinking glass one-half full of h2o, set it on top of the fridge to judge if the unit is leveled.

    • The refrigerator legs should exist adapted for the unit to accept a slight backward slope.

    • Bank check the door alignment.

    • Refer to our LG Refrigerator Leveling Instructions page for a pace past footstep guide.

    • Fifty-fifty if your refrigerator cabinet is leveled, the doors should be properly aligned. If the alignment is off, moisture from the room tin can enter the unit and crusade frost to buildup.

    ADJUSTING THE TEMPERATURE:

    While checking the leveling and alignment of your fridge, you may want to make minor adjustments to the temperature settings. When the refrigerator'due south temperature is too low, it causes frost buildup (because the unit is unable to warm up to cook the previous frost buildup). Once you've confirmed the unit is leveled, raise the temperature for a couple of days and then that the frost will disappear and the noise will stop.

    For your convenience, bookmark this page, and so that you can return here anytime. If your refrigerator is properly leveled, the temperature is adjusted to remove frost, but the noise still persists, the unit may require a repair service. Please visit our Request a Repair page for a professional service.

    Please, DO NOT SKIP this step. Frost buildup on the refrigerator fans will cause noise to your unit if the unit is not leveled properly. Please visit our LG Refrigerator Leveling Instructions before proceeding to the next step.

    Did this step eliminate or reduce the noise?

    Yes No

28. Good job, now that we take been able to reduce the noise of your refrigerator, go along the troubleshooting steps to check for other contributing factors that can lead to refrigerator noises.

    Go on to Next Stride

29. Okay, If you accept tried the steps above, but the noise still persists; the unit may require a repair service. Please visit our Request a Repair page for a professional service. But before you asking for a repair service, nosotros recommend that you go along the troubleshooting steps considering there are other contributing factors that tin can crusade refrigerator noises.

    Proceed to Adjacent Step

31. To sympathize why the alarm beeps while the doors are closed, we need to examination the alarm.

    Steps to follow:

    • Open the refrigerator door and locate the upper hinge.

    • Check if the swivel has a push switch or a reed(magnetic) switch.

    NOTE: The door push switch or magnetic switch is located on the top door swivel of the unit. When the door makes contact with this switch the fridge alert will stop.

    

    • Test the door switch co-ordinate to the switch blazon:

      FOR PUSH SWITCH:

      • Visually inspect the upper hinge to make sure that information technology is flushed against the refrigerator chiffonier properly.

        

      • If it is raised out of position with space, the door may not make contact with the push switch, and the alert may audio when the doors are airtight.

        Steps to follow:

        • Button in the door switch to run across if the door warning stops.

      FOR REED (MAGNETIC) SWITCH:

      • Place a magnet over the switch to come across if the door alert stops.

    Does the alarm turn off?

    Aye No

32. If the warning stops after manually pressing the door switch or holding a magnet over the reed switch, then the doors are non aligned with the switch.
    This tin be resolved past leveling the refrigerator, aligning the doors, or both.

    STEPS TO FOLLOW:

    • Visually inspect the push button or reed switch to ensure that sure it is not stuck or damaged.

    • If the push switch was stuck, make clean the door switch with warm soapy water to reduce the chances of the door switch sticking in the futurity.

    • Level your fridge and align the doors.

      

      Steps for proper leveling:

      The following steps are snippets culled from our detailed article most proper leveling. Please visit our LG Refrigerator Leveling Instructions folio for a step past step guide.

      • Open the refrigerator doors.

      • Place a level on acme of the refrigerator to bank check if the unit is leveled from side to side.

      • If a level is not available, fill a glass half full of water, prepare it on top of the refrigerator to gauge if the unit is leveled.

      • The fridge legs should be adjusted for the unit to have a slight backward slope.

      • Check the door alignment.

      • Even if your fridge cabinet is leveled, the doors should be properly aligned too.

    Note: When the unit is leveled and the doors are aligned correctly, bank check inside the refrigerator to ensure no food items, bins, or drawers are obstructing the door from closing completely.

33. If yous have tried the steps above, and the alarm noise still persists; the unit will require a repair service. Please visit our Request a Repair page for a professional person service.

34. If the door alarm is no longer working, let'southward test to meet if it is turned off, jammed, or requires a technical repair service.

    Steps to follow:

    • Check the command console to meet if the door alarm office has been turned off.

    • Open up the fridge door and locate the upper hinge.

    • Check if the hinge has a push switch or a reed (magnetic) switch.

    Notation: The door push switch, or magnetic switch is ordinarily located at the elevation inner office of the unit (this switch is what the door presses when airtight, information technology shuts off the light and triggers the cooling of the unit).

    

    • Exam the door switch according to the type:

      FOR Button SWITCH: Push-in the door switch to see if the door warning turns back on.

      FOR REED (MAGNETIC) SWITCH: If you accept a reed (magnetic) switch, unfortunately, testing and repairing it requires a technician's help. Please visit our Request a Repair page for a professional service.

    For push switch, does the alarm turn back on?

    Yes No

35. The button switch may be stuck, lift it out gently, and make clean the door switch with warm soapy water to reduce the chances of the door switch sticking in the future.

36. This unit requires a repair service. For your convenience, delight visit our Asking a Repair page for a professional service.

cesarwhoint48.blogspot.com

Source: https://www.lg.com/us/support/help-library/refrigerator-noises-CT00023125-20150292153479

Share this post